4

Setting up WHS with Alternative Disk Drivers

If you are building your own home server you might have a hard disk controller that isn’t supported by Windows Home Server.  It could be a RAID device that you will use in drive only mode or it might be a unit that is quite new and the drivers are not built into the installation media.  Also to get most SATA controllers working in AHCI mode rather than IDE Emulation you will need to install the drivers using this method.

First select to Boot from CD-ROM – if you have a blank hard disk then most systems will automatically boot from CD-ROM if not you will have to tell you computer to boot from a different source by pressing a certain key at boot time to bring up a Boot Menu.  You will need to refer to your motherboard manual , keys such as F10, F2 might work – look carefully at the screen when your PC first switches on for clues as to what key to press.  It is also possible to go into setup and select which source to boot from also.

image

When the CD-ROM boots you get the following screen indicating it’s loading the first stage of the installer into memory

image 

Next the first stage of the installer starts

image

Next the installer is locating hardware and drivers to be used

image

No drivers for the storage controllers have been found – here you are given the opportunity to select additional storage drivers – select “Yes”

image

Select the driver from the floppy and select open:

image

Go through the setup as normal:

image

Select your language.

image

On the next screen select your disk – don’t load the drivers again, you’ve done this already:

image

Select New Installation if you are doing a totally fresh install – if you are wanting to keep data from a previous install then select Recovery:

image

Accept the license agreement:

image

Enter your product key – if you have the trial just hit next:

image

If you didn’t enter a product key you get a warning that you will only have 30 days to use the product:

image

Give your server a name – be aware people will expect you to replace server or myserver with the server name you have chosen if they refer to an address like http://server:55000/ or \\server

image

Select the checkbox to “Acknowledge that all the data on these drives will be lost”

image

Are you really sure? :

image

Then hit start:

image

Formatting the system volume is the first part of the setup:

image

Then the installation files will be copied:

image

Then it’s time for the first reboot – it will happen automatically:

image 

If you get this screen then you left the floppy in the drive. Take it out and press a key:

image,

Be quick and press F6 – you need to install your disk storage drivers again:

image

After a few moments you should get this screen. Press S:

image

Insert your floppy and press Enter:

image

Select your driver by pressing Enter:

image

Now you have installed your driver hit enter to continue:

image

Setup will now continue with the rest of the install:

image

Now the final part of the base OS install process is underway:

image

Finished copying the files:

image

Restarting:

image

Don’t forget to remove the floppy again:

image

Windows Home Server is based on Windows Server 2003 – so don’t be afraid you have setup the wrong OS:

image

Setup will continue the final stage of installation:

image 

Installing devices:

image

Installing Network:

image

Copying more files:

image

Completing installation:

image 

Installing Start menu items:

image

Registering components:

image

Saving settings:

image

Removing temporary files:

image

And the final reboot of installation – can take a few minutes so let the machine be:

image

Hello Home Server:

image

Starting up:

image

Applying computer settings:

image

Applying personalized settings:

image

Again the installation is being finalized – expect to see this ‘final’ screen a few times more.

image

Windows Home Server will reboot itself automatically as it’s finalizing the installation – give it time and soon you’ll have a complete install.

image

It’s normal to see the disk scanning screen after a new install.

image #

Your system might reboot a few more times to install updates and so on but as far as the storage device driver goes you shouldn’t need to interact with the install process again:

image

That’s where I’ll leave it – you should be fine from here on in.

Share this WHS Article with Others:

| |

About the Author

Comments (4)

Trackback URL | Comments RSS Feed

  1. Diehard says:

    Hi,
    Sorry I’m a little confused, why would I be using this method ?

    Is it because I am using a virtual machine setup and WHS has to be pointed to a VHD ?

  2. Awesnduver says:

    Well, this would work great if I had a floppy drive. Like it’s 2010, who has floppy drives now days. Waiting Home Server v2 when we’ll actually see something that hopefully makes installation ourside of OEM easy.

  3. sic0048 says:

    Well, without a floppy drive, it really is much harder. You can successfully install the drivers the first time via a USB stick or CD-Rom, but after the first reboot when you must install them the 2nd time, you really must have a floppy drive or it fails. In the end, without a floppy drive, I think most people end up creating an entirely new installation disk after slip streaming the drivers into it. It is a real pain in the rear that should be made moot with the WHS v2 when it is released.

  4. Very nice information. I will check back definately for more information.

Leave a Reply




If you want a picture to show with your comment, go get a Gravatar.